Mapesil AC Jasmine (130) Silicone

Product Information

Do not use Mapei Mapesil AC Silicone for joints in exterior between ceramic tiles and light-coloured natural stone because dirt could accumulate by the joints. Use Mapei Mapesil LM Silicone. For sealing surfaces sensitive to acids such as lime stone, use a neutral silicone sealant (e.g. Mapesil LM). Do not use Mapei Mapesil LM for sealing doors subject to intense traffic – (use Mapeflex PU45, Mapeflex PU20 or Mapeflex PU21).

After the final cleaning operation, if the surface still has traces of Mapei Ultracolor Plus due to incorrect application, it may be cleaned down with an acidic cleaner (e.g. Keranet), by following the relevant instructions, at least 24 hours after grouting the joints. Only use Keranet on surfaces which are resistant to acid, and never use it on marble or limestone material.

Applying the grout: Fill the joints with the Mapei Ultracolor Plus mix using a special MAPEI grout float or rubber squeegee, without leaving any gaps or steps. Remove any excess of Mapei Ultracolor Plus from the surface, by moving the float diagonally to the joints while the mix is still fresh. Mapei Ultracolor Plus forms a smooth, compact finished surface with optimum resistance to abrasion, compression and flexural strength, and good resistance to acids with a pH > 3. Floors are ready for light foot traffic after approx. 3 hours. Surfaces grouted with Mapei Ultracolor Plus may be put into service after 24 hours. Basins and swimming pools may be filled up 48 hours after grouting. Mapei Mapesil LM does not emit unpleasant odours, and comes in the form of a thixotropic paste. It is easy to apply on vertical and horizontal surfaces and cures at room temperature through the humidity present in the air to form a flexible sealant. Seals made using Mapei Mapesil LM are extremely stable over time, even when exposed to inclement weather, industrial environments, temperature variations or water. The product remains flexible over a temperature range of between -40°C and +150°C. the joint is sized so that the estimated maximum extension is not greater than 25% of the initial width (calculated at +20°C);

Sealing joints between sinks or sanitary ware and ceramic tiles in kitchens, bathrooms and showers with colours coordinated with the Mapei coloured grout ranges. Mapei Ultracolor Plus is available in 2kg and 5kg bags, in the following colours: Please note, only some colours are available in 2kg bags.

Guides & Advice

Under certain conditions Mapei Mapesil LM Silicone may have a water-repellent effect along the edges of joints. This effect is only noticeable when surfaces are wet and is invisible when the same surfaces are dry. This phenomenon, however, has no effect on the product’s performance characteristics. Do not use Mapei Primer FD when sealing stone or marble. All Mapei Ultracolor Plus grout colours are also available in a matching silicone – Mapesil AC Silicone. If using this grout with moisture sensitive natural stone tiles, a low modulus silicone is advised – Mapei Mapesil LM Silicone. Mapei Ultracolor Plus Tile Grout is made up of a blend of special hydraulic binders, graded aggregates, special polymers, water repellent admixtures, organic molecules and pigments. When Mapei Mapesil LM is exposed to the air, the surrounding humidity sets off the cure reaction and the sealant becomes flexible. The surrounding temperature only has a small impact on the cure rate of Mapei Mapesil LM, while the level of humidity in the surrounding air has the most influence. We highly recommend that the product is never applied if the temperature is below 0°C. Mapei Mapesil LM Silicone Sealant is a neutral, mould-resistant silicone sealant with very low emission level of volatile organic compounds (VOC), for use with natural stone and marble.

To control the depth of the joint and to prevent Mapei Mapesil AC Silicone from adhering to the base, the bottom of the joint should be filled with a sized Mapefoam, a polyethylene cord Mapei Ultracolor Plus is suitable for grouting walls and floors in areas that are subject to intense traffic, such as shopping centres, airports, restaurants and other public spaces. It is also suitable for residential use in all areas, such as facades, balconies, terraces and swimming pools. Final cleaning of the powdery film of Mapei Ultracolor Plus from the surface may be carried out with a clean, dry cloth.When Mapesil LM is constantly immersed in treated water typically found in swimming pools its physical-mechanics may be affected prematurely. Given the wide range of products used to treat water and the actual quantities employed, its suitability over long periods may only be guaranteed following specific laboratory testing. Sealing joints in wall and floor coverings of ceramic and cement, provided they are not subject to heavy abrasion. The use of Mapei Mapesil AC is not recommended on highly plasticised material or on bituminous surfaces because of the release of substances that reduce bonding and penetrate into the sealant, altering the colour and resistance. Finishing: When the mix loses its plasticity and becomes opaque, which usually takes place after 15-30 minutes, clean off the excess Ultracolor Plus with a hard, damp sponge (e.g. a MAPEI sponge), working in a diagonal direction to the joints. Rinse the sponge frequently, using two different containers of water: one to remove the excess mix from the sponge, and the other, containing clean water, to rinse the sponge. This operation may also be carried out with a machine with a sponge belt or rotating disc. When the mix is partially set, after 50-60 minutes, a damp Scotch-Brite® sponge or an abrasive felt disc may be passed over the joints to even out the surface. Mapei Ultracolor Plus creates water repellent grout joints that have excellent colour uniformity. All colours are resistant to UV rays and atmospheric agents.

Make sure your tiling project’s joints and seals stand up to everyday wear and tear with Mapesil, an acetic-crosslinking silicone sealant from the world’s leading manufacturer of tiling grout, adhesives and sealing products, Mapei.

Delivery & Returns

Mapei Ultracolor Plus does not contain Portland cement and must not be mixed with gypsum or other hydraulic binders; never add water to the mix once it has started to set. Forming a perfectly elastic gasket between different elements in building, mechanical engineering, ship-building, automobile manufacturing, etc. The resistance of Mapei Mapesil AC to chemical agents is generally excellent; however, due to the numerous products and working conditions to which Mapei Mapesil AC can be applied, it is always advisable to do a sample test in cases of doubt.